Skip to main content

Multiple Choice Interview Questions On Special Motor Part 2

Ques.[1] For torque transmission over a long distance with the help of electrical wires only, which of the following two synchros are used ?

(a)CX and CT
(b)CX and CR
(c)CX and CD
(d)CT and CD
Answer :B 

Ques.[2] Squirrel-cage induction motor is finding increasing application in high-power servo systems because new methods have been found to

(a) increase its rotor resistance
(b) control its torque
(c) decrease its intertia
(d) decouple its torque and flux. 
Answer:D 

Ques.[3] The control ........................ synchro has three- phase winding both on its stator and rotor.

(a) differential
(b) transformer
(c) receiver
(d) transmitter
Answer:A 

Ques.[4] A dc servomotor is similar to a regular d.c. motor except that its design is modified to cope with

(a) electronic switching
(b) slow speeds
(c) static conditions
(d) both (b) and (c). 
Answer:D 

Ques.[4] The low-torque synchros cannot be used for

(a) torque transmission
(b) error detection
(c) instrument servos
(d) robot arm positioning.
Answer:D 

Ques.[5].Which of the following synchros are used for error detection in a servo control system ?

Must Read

  •  Multiple Choice Interview Questions On Special Motor Part 1
  •  Basic Interview Question Of Alternator Part 1
(a) control transmitter
(b) control transformer
(c) control receiver
(d) both (a) and (b).
Answer:D  

Ques.[6] The arrangement required for producing a rotation equal to the sum or difference of the rotation of two shafts consists of the following coupled synchros.

(a) control transmitter
(b) control receiver
(c) control differential transmitter
(d) all of the above.
Answer:D 

Ques.[7] Which of the following motor would suit applications where constant speed is absolutely essential to ensure a consistent product ?

(a) brushless dc motor
(b) disk motor
(c) permanent-magnet synchronous motor
(d) stepper motor.
Answer:C 

Ques.[8] A switched reluctance motor differs from a VR stepper motor in the sense that it

(a) has rotor poles of ferromagnetic material
(b) rotates continuously
(c) is designed for open-loop operation only
(d) has lower efficiency.
Answer:B 

Ques.[9] The electrical displacement between the two stator windings of a resolver is

(a) 120º
(b) 90º
(c) 60º
(d) 45º
Answer:B 

Ques.[10] Which of the following motor runs from a low dc supply and has permanently magnetized salient poles on its rotor ?

(a) permanent-magnet d.c. motor
(b) disk d.c. motor
(c) permanent-magnet synchronous motor
(d) brushless d.c. motor.
Answer:A 

Ques.[11] Regarding voltages induced in the three stator windings of a synchro, which statement is false ?

(a) they depend on rotor position.
(b) they are in phase.
(c) they differ in magnitude.
(d) they are polyphase voltages. 
Answer:D

Ques.[12] A dc servomotor is similar to a regular d.c. motor except that its design is modified to cope with

(a) electronic switching
(b) slow speeds
(c) static conditions
(d) both (b) and (c).
Answer:D 

Ques.[13] One of the basic requirements of a servomotor is that it must produce high torque at all

(a) loads
(b) frequencies
(c) speeds
(d) voltages.
Answer:C 

Ques.[14] The most common two-phase ac servomotor differs from the standard ac induction motor because it has

(a) higher rotor resistance
(b) higher power rating
(c) motor stator windings
(d) greater inertia.
Answer:A 

Ques.[15] Though structurally similar to a control transmitter, a control receiver differs from it in the following way :

(a) it has three-phase stator winding
(b) it has a rotor of dumbell construction
(c) it has a mechanical damper on its shaft
(d) it has single-phase rotor excitation.
Answer:C

Ques.[16] A switched reluctance motor differs from a VR stepper motor in the sense that it

(a) has rotor poles of ferromagnetic material
(b) rotates continuously
(c) is designed for open-loop operation only
(d) has lower efficiency. 
Answer:B 
Labels:

Comments

Post a Comment

Comment Policy
We’re eager to see your comment. However, Please Keep in mind that all comments are moderated manually by our human reviewers according to our comment policy, and all the links are nofollow. Using Keywords in the name field area is forbidden. Let’s enjoy a personal and evocative conversation.

Popular posts from this blog

Practical Commutation

The e.m.f. induced in each coil of armature is alternating in nature. If load is connected, the current flowing will also be alternating. But the flow of current in a d.c. generator must be undirectional. This can be achieved by the use of commutator. When the armature conductors are under the influence of one pole they carry current in one direction whereas the current is reversed when the conductors are under the influence of other pole. This reversal of current takes place along the magnetic neutral axis. Fig. 1 Note : The reversal of current is likely to take place in short interval when a coil is short circuited by a brush so that transfer of current from one direction to other is carried out without any sparking. This process is called commutation.        Thus a process by which current in the short circuited coil is reversed while it crosses the MNA is called commutation. The time during which the coil remains short circuited is known as...
1 comment
Read more

Demagnetising and Cross Magnetizing Conductors

The conductors which are responsible for producing demagnetizing and distortion effects are shown in the Fig.1. Fig. 1        The brushes are lying along the new position of MNA which is at angle θ  from GNA. The conductors in the region AOC = BOD = 2θ  at the top and bottom of the armature are carrying current in such a direction as to send the flux in armature from right to left. Thus these conductors are in direct opposition to main field and called demagnetizing armature conductors.         The remaining armature conductors which are lying in the region AOD and BOC carry current in such a direction as to send the flux pointing vertically downwards i.e. at right angles to the main field flux. Hence these conductors are called cross magnetizing armature conductors which will cause distortion in main field flux.        These conductors are shown in the Fig. 2 Fig. 2  ...
Post a Comment
Read more

Winding Pitches

Now we will consider the definitions of different types of winding pitches, required in the design of the armature winding. 1.1 Back Pitch         The distance which is measured interns of armature conductors i.e. between top and bottom coil sides of a coil measured around the back of the armature i.e. away from the commutator is called back pitch and is denoted by . It is measured interms of coil sides. Note : Since it is difference between odd and even number, it is always odd number.        The size of the coil is decided by the back pitch. The back pitch is normally equal to coilsides per pole. It is shown for lap and wave type of winding in the Fig. 1. Fig. 1        The back pitch for the winding shown in the Fig. 1 is y b = 14 - 1 = 13 as coilsides 1and 14 are of coil number 1. 1.2 Front Pitch        It is defined as the distance measured between two c...
Post a Comment
Read more